[OpenSIPS-Users] dispatcher not doing fail over itself

[Bogdan-Andrei Iancu]

dst is null as there is no pending destination for failover. cnt is 1.

Which OpenSIPS revision are you using ?

Regards,

Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com

On 17.09.2014 19:04, Satish Patel wrote:
> I just trying to print $avp(271) $avp(272) and $avp(273)
>
> I am getting following output, why dst_avp is null ? and cnt_avp 
> should be 2 right?
>
>  dst_avp = <null>
>  grp_avp = 1
>  cnt_avp = 0
>
> Notes: I have both Freeswitch instance running on same box but 
> different port, do you think because of that it think it is single host?
>
> PARTITION:: default
>         SET:: 1
>                 URI:: sip:sip.example.com:5061 
> <http://sip.example.com:5061> state=Active
>                 URI:: sip:sip.example.com:5071 
> <http://sip.example.com:5071> state=Active
>
>
> On Wed, Sep 17, 2014 at 11:06 AM, Satish Patel <satish.txt at gmail.com 
> <mailto:satish.txt at gmail.com>> wrote:
>
>     Here you go
>
>
>
>
>     /sbin/opensips[28000]: Sending call to ===> Freeswitch
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     p=0x7f9ed01dd420, flags=0x0000
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     #011#011#011name=<274>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<10>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     #011#011#011val_int=<0>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     p=0x7f9ed01df208, flags=0x0000
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     #011#011#011name=<273>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<9>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     #011#011#011val_int=<1>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     p=0x7f9ed01e6518, flags=0x0002
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     #011#011#011name=<272>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<12>
>     /sbin/opensips[28000]: INFO:avpops:ops_print_avp:
>     #011#011#011val_str=< / 0>
>     /sbin/opensips[28000]: dispatcher: Attempting to dispatch call to
>     sip:182.xx.xx.xxx:5071
>     /sbin/opensips[28005]: Inside dispatcher failure route
>     /sbin/opensips[28005]: ds_dispatcher <null> <null> > <null>
>     /sbin/opensips[28005]:
>     R-DISPATCHER-ROLLOVER:fU4SNHMvcNmnjW19gsSj0g..-S No more gateways
>     in route set
>
>
>     On Wed, Sep 17, 2014 at 10:25 AM, Bogdan-Andrei Iancu
>     <bogdan at opensips.org <mailto:bogdan at opensips.org>> wrote:
>
>         Hi,
>
>         As mentioned, place the avp_print() just after you did the
>         ds_select_dst(), before relaying to the first destination.
>
>         Regards,
>
>         Bogdan-Andrei Iancu
>         OpenSIPS Founder and Developer
>         http://www.opensips-solutions.com
>
>         On 17.09.2014 14:09, Satish Patel wrote:
>
>             Confirmed  probing/inactive thing is working,
>
>             Now problem is failover not working, ds_next_dst() not
>             able to find next gateway and it says no more gateway
>             available. If you check my script, i am calling failure
>             route and inside it calling ds_next_dst() but you are
>             saying do avp_print() on ds_select_dst() it won't print
>             anything because after failure you are in failure route block.
>
>             Please advice if my script has any issue.
>
>             Sent from my iPhone
>
>             On Sep 17, 2014, at 3:30 AM, Bogdan-Andrei Iancu
>             <bogdan at opensips.org <mailto:bogdan at opensips.org>> wrote:
>
>                 Hi Satish,
>
>                 Use the "opensipsctl fifo ds_list" to see the status
>                 of the gws in realtime . Be sure that once a gw is in
>                 non-active state (probing or inactive), it will not be
>                 used again for routing. Just take care of doing the
>                 ds_next_dst() in order to jump to the next available gw.
>
>                 If you do the avp_print() after ds_select_dst(), you
>                 can see how many other gw are prepared to used in case
>                 of failover.
>
>                 Regards,
>
>                 Bogdan-Andrei Iancu
>                 OpenSIPS Founder and Developer
>                 http://www.opensips-solutions.com
>
>                 On 16.09.2014 21:02, Satish Patel wrote:
>
>                     After doing couple of TEST look like its marking
>                     "Probing" for failed gateway but not auto failover
>                     to next gateway, i meant call get disconnect and i
>                     need to re-initiate call then all call goes to
>                     second active gateway..
>
>                     I believe it should first mark gateway "Probing"
>                     and then fall-back to second gateway automatically
>                     instead of call disconnect and i am getting 503
>                     error code on my SIP Phone.
>
>
>
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.opensips.org/pipermail/users/attachments/20140919/c734ecae/attachment-0001.htm>