[OpenSIPS-Users] help in configuring load balancer for outbound dial

[Leo Thomas Selvaraj]

The initial five calls end and then I do  a reload and then I place a call
it works. If I don’t do a reload after the end of the initial five calls the
6th call fails.

Thanks,

Leo Thomas Selvaraj 
 T: +1 609-987-0044 x 139 | F: +1 609-987-9787


 The information contained in this e-mail message or messages (which
includes any attachments) is confidential and may be legally privileged. It
is intended only for the use of the person or entity to which it is
addressed.


-----Original Message-----
From: Bogdan-Andrei Iancu [mailto:bogdan at voice-system.ro] 
Sent: Thursday, June 11, 2009 10:46 AM
To: leo at servion.com
Cc: users at lists.opensips.org
Subject: Re: [OpenSIPS-Users] help in configuring load balancer for outbound
dial

Aha, so you make 5 calls, the 6th fails. then you do a reload and the 
initial 5 calls end. When you try to place a new call is not working?  
Correct?

Regards,
Bogdan

Leo Thomas Selvaraj wrote:
> The initial five calls is terminated. I tried to make the next set of
calls
> only after all the previous calls were terminated.
>
> Thanks,
>
> Leo Thomas Selvaraj 
>  T: +1 609-987-0044 x 139 | F: +1 609-987-9787
>
>
>  The information contained in this e-mail message or messages (which
> includes any attachments) is confidential and may be legally privileged.
It
> is intended only for the use of the person or entity to which it is
> addressed.
>
> -----Original Message-----
> From: Bogdan-Andrei Iancu [mailto:bogdan at voice-system.ro] 
> Sent: Thursday, June 11, 2009 5:27 AM
> To: leo at servion.com
> Cc: users at lists.opensips.org
> Subject: Re: [OpenSIPS-Users] help in configuring load balancer for
outbound
> dial
>
> Hi Leo,
>
> So you do the lb_reload without changing anything in DB and then you try 
> to establish some new calls, which fail...ok. But my question was - the 
> initial 5 calls you set before the reload, are still ongoing? or they 
> are terminated?
>
> Regards,
> Bogdan
>
> Leo Thomas Selvaraj wrote:
>   
>> Bogdan,
>>
>>  
>>
>> Please find my response below in red.
>>
>>  
>>
>> Leo Thomas Selvaraj 
>>
>>  T: +1 609-987-0044 x 139 | F: +1 609-987-9787
>>
>>  
>>
>>  
>>
>>  The information contained in this e-mail message or messages (which 
>> includes any attachments) is confidential and may be legally 
>> privileged. It is intended only for the use of the person or entity to 
>> which it is addressed.
>>
>>  
>>
>>  
>>
>> -----Original Message-----
>> From: Bogdan-Andrei Iancu [mailto:bogdan at voice-system.ro]
>> Sent: Wednesday, June 10, 2009 2:17 PM
>> To: leo at servion.com
>> Cc: users at lists.opensips.org
>> Subject: Re: [OpenSIPS-Users] help in configuring load balancer for 
>> outbound dial
>>
>>  
>>
>> Hi Leo,
>>
>>  
>>
>> so shortly, your case is:
>>
>>  
>>
>> 1) you successfully do LB until all the destination are full (5 calls) 
>> *-- yes*
>>
>> -> then load_balance() returns false in script -*--- yes*
>>
>>  
>>
>> 2) you do a lb_reload - what do you change in the table?  *I did not 
>> change anything in the table. I simply issue lb_reload*
>>
>>  
>>
>> 3) you try do route call again and still fails ?   are the initial 5 
>>    *only initial 5 calls work. After that all the call fails unless I 
>> issue lb_reload from command line or restart opensips*.
>>
>> calls still going?  *We are evaluating opensips and I am responsible 
>> for implementation/decision.*
>>
>>  
>>
>> Regards,
>>
>> Bogdan
>>
>>  
>>
>> Leo Thomas Selvaraj wrote:
>>
>>     
>>> Hi,
>>>       
>>> I had configured load balancer for outdialing. load_balancer table
>>>       
>>> information mentioned below.
>>>       
>>>  +----+----------+------------------+-----------+---------------+
>>>       
>>>  | id | group_id | dst_uri          | resources | description   |
>>>       
>>>  +----+----------+------------------+-----------+---------------+
>>>       
>>>  |  1 |        1 | sip:10.128.22.38 | pstn=2    | standby gw    |
>>>       
>>>  |  2 |        1 | sip:10.128.22.45 | pstn=3    | production gw |
>>>       
>>>  +----+----------+------------------+-----------+---------------+
>>>       
>>> The load balancer is working correctly for the first cycle, I try to
>>>       
>>> make five calls and it makes two calls to .38 gateway and then three
>>>       
>>> calls to .45 gateway. After completing one cycle the $du value is
>>>       
>>> setting as null if I try to make subsequent calls and the calls were
>>>       
>>> failing.  If I issue lb_reload using MI from command line  (
>>>       
>>> opensipsctl fifo lb_reload ) it starts again. I want this to run
>>>       
>>> continuously without issuing any MI commands.
>>>       
>>> From the logs I can see that $du is set to null. I am not sure whether
>>>       
>>> I am making any mistake.
>>>       
>>> I think something is wrong in setting the profile and fetching data
>>>       
>>> for the profile using get_profile_size in do_load_balancer function in
>>>       
>>> lb_data.c. The profile is getting set as *lbXpstn*, but when I tried
>>>       
>>> to print the value res[k]->profile it always displays a junk value.
>>>       
>>> Thanks,
>>>       
>>> *Leo Thomas Selvaraj*
>>>       
>>>  T: +1 609-987-0044 x 139 | F: +1 609-987-9787
>>>       
>>> ------------------------------------------------------------------------
>>>       
>>> cid:image001.gif at 01C97492.FCB6B790
>>>       
>>>  The information contained in this e-mail message or messages (which
>>>       
>>> includes any attachments) is confidential and may be legally
>>>       
>>> privileged. It is intended only for the use of the person or entity to
>>>       
>>> which it is addressed.
>>>       
>>> ------------------------------------------------------------------------
>>>       
>>> _______________________________________________
>>>       
>>> Users mailing list
>>>       
>>> Users at lists.opensips.org
>>>       
>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>>       
>>>  
>>>       
>>  
>>
>>     
>
>
>
>