[OpenSIPS-Users] Dialog count mismatches

[Bogdan-Andrei Iancu]

no, the dialog module count all ongoing dialog (disregarding the state 
they are). A dialog is considered onoging since the INVITE was sent out, 
till the BYE was received.

You do not have to do anything special on reply time.

Regards,
Bogdan

brett at nemeroff.com wrote:
> Is there a way to control that behavior to only count active and not early? Just curious. So does that mean I shouldn't have to check for the 200 Reply before I set the profile??
> -Brett
>
> Sent from my Verizon Wireless BlackBerry
>
> -----Original Message-----
> From: Bogdan-Andrei Iancu <bogdan at voice-system.ro>
>
> Date: Wed, 26 Aug 2009 22:04:02 
> To: OpenSIPS users mailling list<users at lists.opensips.org>
> Subject: Re: [OpenSIPS-Users] Dialog count mismatches
>
>
> Hi Brett,
>
> There was a bug in dialog module, in counting the dialogs in a profile - 
> the bug was fixed last week and it will be part of 1.5.3 that will be 
> released tomorrow.
>
> The bug consisted in counting also dialogs that were in DELETED state 
> (instead of counting only the EARLY and ACTIVE ones). The dialogs are 
> kept in DELETED state for like 5sec after the BYE.
>
> Try to upgrade from svn and see if the counting is now correct.
>
> Regards,
> Bogdan
>
> Brett Nemeroff wrote:
>   
>> All,
>> I'm running OpenSIPs 1.5.1. I use dialog profiling to "count" calls 
>> up. I notice that comparing my numbers to my providers using SBCs that 
>> my numbers are always MUCH higher than my provider for 
>> "simultaneous calls connected". For example, I may show 300 calls up, 
>> but they only show 75. The numbers are usually out of whack like this. 
>> The weird thing is, in very small quantities, 2-3 calls, I'm *sure* 
>> the numbers match.  Also, if they stop dialing entirely and I let the 
>> calls die off, the numbers return to 0 quickly enough. 
>>
>> To set my dialog profile, I do it in the onreply route like this:
>>         if (t_check_status("200")) {
>>                 # Set my dialogs here
>>                 if (!is_in_profile("account","$avp(s:accountid)")) {
>>                         set_dlg_profile("account","$avp(s:accountid)");
>>                 }
>>                 if (!is_in_profile("trunk","$avp(s:trunkid)")) {
>>                         set_dlg_profile("trunk","$avp(s:trunkid)");
>>                 }
>>
>>         }
>>
>>
>> Any thoughts on what I may be doing wrong? BTW, I do this in the 
>> onreply and not in the original INVITE because I'm trying to mimick 
>> the behavior of a nextone SBC which limits the number of CONNECTED 
>> calls, but doesn't limit the call setups. I think that's a silly way 
>> to do it, but if I don't match the behavior, nextone SBCs will show 
>> horrible ASRs for me as they'll continue to setup calls long after I 
>> start rejecting calls because too many are being set up.
>>
>> Thoughts? Thanks!
>> -Brett
>>
>>
>>
>> Thanks,
>> Brett
>>
>>
>>
>> from opensips -V: @(#) $Id: main.c 5469 2009-03-18 12:43:10Z 
>> bogdan_iancu $
>>
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> Users mailing list
>> Users at lists.opensips.org
>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>   
>>     
>
>
> _______________________________________________
> Users mailing list
> Users at lists.opensips.org
> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
> _______________________________________________
> Users mailing list
> Users at lists.opensips.org
> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>
>