[OpenSIPS-Users] Dialog information tracing in opensips Issue

[urmi lakkad]

Hello Bogdan,

Thank you very much for your quick response.
Here I have attached OpenSIPs call log.

-Urmi


On Tue, Aug 25, 2009 at 3:54 PM, Bogdan-Andrei Iancu <bogdan at voice-system.ro
> wrote:

> Looks good - can you post the opensips logs (in debug=6) for this single
> call ? just to verify.
>
> Regards,
> Bogdan
>
> urmi lakkad wrote:
> > Hello Bogdan,
> >
> > Thank you for ur response.
> >
> > Here with this mail I have _attached my SIP call capture_ using ngrep.
> > So, please find the attachment. and do needful.
> >
> >
> > -Thanks
> > Urmi
> >
> > On Tue, Aug 25, 2009 at 12:41 PM, Bogdan-Andrei Iancu
> > <bogdan at voice-system.ro <mailto:bogdan at voice-system.ro>> wrote:
> >
> >     Post the SIP capture of the call you are testing with. Use "ngrep
> >     -d any
> >     . port 5060" to get the capture - this will solve the mystery.
> >
> >     Regards,
> >     Bogdan
> >
> >     urmi lakkad wrote:
> >     > Hello,
> >     >
> >     > Can u please suggest me some solution of my problem of DIALLOG
> >     module ?
> >     >
> >     > Thank you for your attention.
> >     >
> >     > -Urmi
> >     >
> >     > 2009/8/21 urmi lakkad <urmi.lakkad at gmail.com
> >     <mailto:urmi.lakkad at gmail.com>
> >     > <mailto:urmi.lakkad at gmail.com <mailto:urmi.lakkad at gmail.com>>>
> >     >
> >     > Hello Brett,
> >     >
> >     > Thank you very much for quick response.
> >     >
> >     > My calls are working fine. I have checked through SIPp and also
> >     > with Grandstream Phones. The call is working fine with out
> >     > failure. At the time of call, I have started the wireshark to
> >     > capture the packets, but there also I m not getting any negative
> >     > reply like 400 or 300.
> >     >
> >     > See, my call is working fine, call dialog created successfully,
> >     > but after that it destroyed, again new dialog is created n that
> >     > too destroy. For a single call it creates 2 dialogs. But that
> >     > dialog entry is not going to DB. Please suggest me the right thing
> >     > to do.
> >     >
> >     > Thanks a lot for your attention.
> >     >
> >     >
> >     > -Urmi
> >     >
> >     >
> >     >
> >     > On Thu, Aug 20, 2009 at 7:38 PM, Brett Nemeroff
> >     > <brett at nemeroff.com <mailto:brett at nemeroff.com>
> >     <mailto:brett at nemeroff.com <mailto:brett at nemeroff.com>>> wrote:
> >     >
> >     > Urmi,
> >     > You log shows the call having failed. I'm not sure why you
> >     > think it runs for the proper duration. But as far as OpenSIPs
> >     > is concerned, the call failed. It's likely a problem in your
> >     > sipp scenario. It's very possible that sipp thinks the call is
> >     > up, but the proxy does not.
> >     >
> >     > In any case, OpenSIPs is behaving as expected, the call fails,
> >     > the dialog is destroyed.
> >     > Aug 19 17:46:27 [6060] DBG:dialog:next_state_dlg: dialog
> >     > 0x2aaaad55af90 changed from state 1 to state 5, due event 1
> >     > Aug 19 17:46:27 [6060] DBG:dialog:dlg_onreply: dialog
> >     > 0x2aaaad55af90
> >     > failed (negative reply)
> >     >
> >     > BTW, a negative reply is >=400 (or may also include >= 300,
> >     > can't remember). Check your traces, see where that comes from.
> >     > -Brett
> >     >
> >     > On Thu, Aug 20, 2009 at 9:02 AM, urmi lakkad
> >     > <urmi.lakkad at gmail.com <mailto:urmi.lakkad at gmail.com>
> >     <mailto:urmi.lakkad at gmail.com <mailto:urmi.lakkad at gmail.com>>>
> wrote:
> >     >
> >     > Hello Stanisław Pitucha,
> >     >
> >     > Thank you for support.
> >     >
> >     > No, My call is established perfectly and is running for
> >     > the specified duration without fail.
> >     > I m firing the call using SIPp.
> >     >
> >     > Also, the dialog state gives me 1.
> >     >
> >     > Thanks for ur attention.
> >     >
> >     > -Urmi
> >     >
> >     > 2009/8/20 Stanisław Pitucha <viraptor at gmail.com
> >     <mailto:viraptor at gmail.com>
> >     > <mailto:viraptor at gmail.com <mailto:viraptor at gmail.com>>>
> >     >
> >     > 2009/8/20 urmi lakkad <urmi.lakkad at gmail.com
> >     <mailto:urmi.lakkad at gmail.com>
> >     > <mailto:urmi.lakkad at gmail.com <mailto:urmi.lakkad at gmail.com>>>:
> >     > > Am I doing right or not ? If not, please tell me the
> >     > correct way.
> >     > > One more thing, Is my configuration is correct or not ??
> >     >
> >     > It looks like your call doesn't even get accepted:
> >     > Aug 19 17:46:27 [6060] DBG:dialog:next_state_dlg: dialog
> >     > 0x2aaaad55af90 changed from state 1 to state 5, due
> >     > event 1
> >     > Aug 19 17:46:27 [6060] DBG:dialog:dlg_onreply: dialog
> >     > 0x2aaaad55af90
> >     > failed (negative reply)
> >     >
> >     > Maybe you require authentication, or something else?
> >     > Just take care of
> >     > the call not failing first. So far it's rejected
> >     > before an OK answer
> >     > (state 1 is "after sending an INVITE", state 5 is
> >     > "deleted" - more or
> >     > less).
> >     > Capture the traffic and see what's going on.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.opensips.org/pipermail/users/attachments/20090825/18cdb9c7/attachment.htm