|
Documentation |
Documentation -> Manuals -> Manual 1.6 -> Types of routesPages for other versions: devel 3.5 3.4 Older versions: 3.3 3.2 3.1 3.0 2.4 2.3 2.2 2.1 1.11 1.10 1.9 1.8 1.7 1.6 1.5 1.4
Table of Content (hide) OpenSIPS routing logic uses several types of routes. Each type of route is triggered by a certain event and allows you to process a certain type of message (request or reply). 1. routeRequest routing block. It contains a set of actions to be taken for SIP requests. Triggered by : receiving an external request from the network. Processing : the triggering SIP request. Type : initially stateless, may be forced to stateful by using TM functions. Default action : if the request is not either forwarded nor replied, the route will simply discard the request at the end. The main 'route' block identified by 'route{...}' or 'route[0]{...}' is executed for each SIP request. The implicit action after execution of the main route block is to drop the SIP request. To send a reply or forward the request, explicit actions must be called inside the route block. Example of usage:
route {
if(is_method("OPTIONS")) {
# send reply for each options request
sl_send_reply("200", "ok");
exit();
}
route(1);
}
route[1] {
# forward according to uri
forward();
}
Note that if a 'route(X)' is called from a 'branch_route[Y]' then in 'route[X]' is just processed each separate branch instead of all branches together as occurs in main route. 2. branch_routeRequest's branch routing block. It contains a set of actions to be taken for each branch of a SIP request. Triggered by : preparation a new branch (of a request); the branch is well formed, but not yet sent out. Processing : the SIP request (with the branch particularities, like RURI, branch flags) Type : stateful Default action : if the branch is not dropped (via "drop" statement), the branch will be automatically sent out. It is executed only by TM module after it was armed via t_on_branch("branch_route_index"). Example of usage:
route {
lookup("location");
t_on_branch("1");
if(!t_relay()) {
sl_send_reply("500", "relaying failed");
}
}
branch_route[1] {
if(uri=~"10\.10\.10].10") {
# discard branches that go to 10.10.10.10
drop();
}
}
3. failure_routeFailed transaction routing block. It contains a set of actions to be taken each transaction that received only negative replies (>=300) for all branches. Triggered by : receiving or generation(internal) of a negative reply that completes the transaction (all branches are terminated with negative replies) Processing : the original SIP request (that was sent out) Type : stateful Default action : if no new branch is generated or no reply is forced over, by default, the winning reply will be sent back to UAC. The 'failure_route' is executed only by TM module after it was armed via t_on_failure("failure_route_index"). Note that in 'failure_route' is processed the request that initiated the transaction, not the reply . Example of usage:
route {
lookup("location");
t_on_failure("1");
if(!t_relay()) {
sl_send_reply("500", "relaying failed");
}
}
failure_route[1] {
if(is_method("INVITE")) {
# call failed - relay to voice mail
t_relay("udp:voicemail.server.com:5060");
}
}
4. onreply_routeReply routing block. It contains a set of actions to be taken for SIP replies. Triggered by : receiving of a reply from the network Processing : the received reply Type : stateful (if bound to a transaction) or stateless (if global reply route). Default action : if the reply is not dropped (only provisional replies can be), it will be injected and processed by the transaction engine. There are three types of onreply routes:
Certain 'onreply_route' blocks can be executed by TM module for special replies. For this, the 'onreply_route' must be armed for the SIP requests whose replies should be processed within it, via t_on_reply("onreply_route_index").
route {
seturi("sip:bob@opensips.org"); # first branch
append_branch("sip:alice@opensips.org"); # second branch
t_on_reply("global"); # the "global" reply route
# is set the whole transaction
t_on_branch("1");
t_relay();
}
branch_route[1] {
if ($rU=="alice")
t_on_reply("alice"); # the "alice" reply route
# is set only for second branch
}
onreply_route {
xlog("OpenSIPS received a reply from $si\n");
}
onreply_route[alice] {
xlog("received reply on the branch from alice\n");
}
onreply_route[global] {
if (t_check_status("1[0-9][0-9]")) {
setflag(1);
log("provisional reply received\n");
if (t_check_status("183"))
drop;
}
}
5. error_routeThe error route is executed automatically when a parsing error occurred during SIP request processing. This allow the administrator to decide what to do in case of error. Triggered by : parsing error in "route" Processing : failed request Type : stateless (recommended) Default action : discard request. In error_route, the following pseudo-variables are available to get access to error details:
error_route {
xlog("--- error route class=$(err.class) level=$(err.level)
info=$(err.info) rcode=$(err.rcode) rreason=$(err.rreason) ---\n");
xlog("--- error from [$si:$sp]\n+++++\n$mb\n++++\n");
sl_send_reply("$err.rcode", "$err.rreason");
exit;
}
6. local_routeThe local route is executed automatically when a new SIP request is generated by TM, internally (no UAC side). This is a route intended to be used for message inspection, accounting and for applying last changes on the message headers. Routing and signaling functions are not allowed. Triggered by : TM generating a brand new request Processing : the new request Type : stateful Default action : send the request out
local_route {
if (is_method("INVITE") && $ru=~"@foreign.com") {
append_hf("P-hint: foreign request\r\n");
exit;
}
if (is_method("BYE") ) {
acc_log_request("internally generated BYE");
}
}
7. startup_routeThe startup_route is executed only once when OpenSIPS is started and before the processing of SIP messages begins. This is useful if some initiation actions are needed, like loading some data in the cache, to ease up the future processing. Notice that this route, compared to the others is not triggered at the receipt of a message, so the functions that can be called here must not do processing on the message. Triggered : At startup, before the listener processes are started. Processing : Initializing functions.
startup_route {
avp_db_query("select gwlist where ruleid==1",$avp(i:100));
cache_store("local", "rule1", "$avp(i:100)");
}
8. timer_routeThe timer_route is as the name suggests, a route executed periodically at a configured interval of time specified next to the name(in seconds). The same as the startup_route, this route does not process a message. You can defined more timer routes. Triggered by : The time keeper. Processing : Functions that do refresh actions.
timer_route[gw_update, 300] {
avp_db_query("select gwlist where ruleid==1",$avp(i:100));
$shv(i:100) =$avp(i:100);
}
|