[OpenSIPS-Users] help in configuring load balancer for outbound dial

Bogdan-Andrei Iancu bogdan at voice-system.ro
Thu Jun 11 16:45:43 CEST 2009


Aha, so you make 5 calls, the 6th fails. then you do a reload and the 
initial 5 calls end. When you try to place a new call is not working?  
Correct?

Regards,
Bogdan

Leo Thomas Selvaraj wrote:
> The initial five calls is terminated. I tried to make the next set of calls
> only after all the previous calls were terminated.
>
> Thanks,
>
> Leo Thomas Selvaraj 
>  T: +1 609-987-0044 x 139 | F: +1 609-987-9787
>
>
>  The information contained in this e-mail message or messages (which
> includes any attachments) is confidential and may be legally privileged. It
> is intended only for the use of the person or entity to which it is
> addressed.
>
> -----Original Message-----
> From: Bogdan-Andrei Iancu [mailto:bogdan at voice-system.ro] 
> Sent: Thursday, June 11, 2009 5:27 AM
> To: leo at servion.com
> Cc: users at lists.opensips.org
> Subject: Re: [OpenSIPS-Users] help in configuring load balancer for outbound
> dial
>
> Hi Leo,
>
> So you do the lb_reload without changing anything in DB and then you try 
> to establish some new calls, which fail...ok. But my question was - the 
> initial 5 calls you set before the reload, are still ongoing? or they 
> are terminated?
>
> Regards,
> Bogdan
>
> Leo Thomas Selvaraj wrote:
>   
>> Bogdan,
>>
>>  
>>
>> Please find my response below in red.
>>
>>  
>>
>> Leo Thomas Selvaraj 
>>
>>  T: +1 609-987-0044 x 139 | F: +1 609-987-9787
>>
>>  
>>
>>  
>>
>>  The information contained in this e-mail message or messages (which 
>> includes any attachments) is confidential and may be legally 
>> privileged. It is intended only for the use of the person or entity to 
>> which it is addressed.
>>
>>  
>>
>>  
>>
>> -----Original Message-----
>> From: Bogdan-Andrei Iancu [mailto:bogdan at voice-system.ro]
>> Sent: Wednesday, June 10, 2009 2:17 PM
>> To: leo at servion.com
>> Cc: users at lists.opensips.org
>> Subject: Re: [OpenSIPS-Users] help in configuring load balancer for 
>> outbound dial
>>
>>  
>>
>> Hi Leo,
>>
>>  
>>
>> so shortly, your case is:
>>
>>  
>>
>> 1) you successfully do LB until all the destination are full (5 calls) 
>> *-- yes*
>>
>> -> then load_balance() returns false in script -*--- yes*
>>
>>  
>>
>> 2) you do a lb_reload - what do you change in the table?  *I did not 
>> change anything in the table. I simply issue lb_reload*
>>
>>  
>>
>> 3) you try do route call again and still fails ?   are the initial 5 
>>    *only initial 5 calls work. After that all the call fails unless I 
>> issue lb_reload from command line or restart opensips*.
>>
>> calls still going?  *We are evaluating opensips and I am responsible 
>> for implementation/decision.*
>>
>>  
>>
>> Regards,
>>
>> Bogdan
>>
>>  
>>
>> Leo Thomas Selvaraj wrote:
>>
>>     
>>> Hi,
>>>       
>>> I had configured load balancer for outdialing. load_balancer table
>>>       
>>> information mentioned below.
>>>       
>>>  +----+----------+------------------+-----------+---------------+
>>>       
>>>  | id | group_id | dst_uri          | resources | description   |
>>>       
>>>  +----+----------+------------------+-----------+---------------+
>>>       
>>>  |  1 |        1 | sip:10.128.22.38 | pstn=2    | standby gw    |
>>>       
>>>  |  2 |        1 | sip:10.128.22.45 | pstn=3    | production gw |
>>>       
>>>  +----+----------+------------------+-----------+---------------+
>>>       
>>> The load balancer is working correctly for the first cycle, I try to
>>>       
>>> make five calls and it makes two calls to .38 gateway and then three
>>>       
>>> calls to .45 gateway. After completing one cycle the $du value is
>>>       
>>> setting as null if I try to make subsequent calls and the calls were
>>>       
>>> failing.  If I issue lb_reload using MI from command line  (
>>>       
>>> opensipsctl fifo lb_reload ) it starts again. I want this to run
>>>       
>>> continuously without issuing any MI commands.
>>>       
>>> From the logs I can see that $du is set to null. I am not sure whether
>>>       
>>> I am making any mistake.
>>>       
>>> I think something is wrong in setting the profile and fetching data
>>>       
>>> for the profile using get_profile_size in do_load_balancer function in
>>>       
>>> lb_data.c. The profile is getting set as *lbXpstn*, but when I tried
>>>       
>>> to print the value res[k]->profile it always displays a junk value.
>>>       
>>> Thanks,
>>>       
>>> *Leo Thomas Selvaraj*
>>>       
>>>  T: +1 609-987-0044 x 139 | F: +1 609-987-9787
>>>       
>>> ------------------------------------------------------------------------
>>>       
>>> cid:image001.gif at 01C97492.FCB6B790
>>>       
>>>  The information contained in this e-mail message or messages (which
>>>       
>>> includes any attachments) is confidential and may be legally
>>>       
>>> privileged. It is intended only for the use of the person or entity to
>>>       
>>> which it is addressed.
>>>       
>>> ------------------------------------------------------------------------
>>>       
>>> _______________________________________________
>>>       
>>> Users mailing list
>>>       
>>> Users at lists.opensips.org
>>>       
>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
>>>       
>>>  
>>>       
>>  
>>
>>     
>
>
>
>   




More information about the Users mailing list